Applies to: Peak, Summit
We recommend you update the firmware of your Peak/Summit using Novation Components. Components is available at components.novationmusic.com and a standalone (non-web based) version is available in your Novation account once you have registered your Peak.
Components is a content manager for Novation products including Peak/Summit and is the best way to ensure that your product is up-to-date with the latest firmware. It also allows you to back up and restore your patches and other content from your device.
If you prefer to update your Peak manually, please carefully follow the below instructions.
Peak instructions:
- Download the attached 'Peak 1.2.1.zip' (or 'Peak 1.3.zip') file from the bottom of this article and unzip it. You will find two files contained within it, 'Peak-363.syx' (or 'Peak-399.syx') and 'PeakFpga_353.syx'.
- Ensure the USB cable from Peak is connected to the computer. Start Peak in Bootloader mode by pressing the 3 buttons on the left side of the screen while powering on the Peak.
- Install and open SysEx Librarian, snoize.com/SysExLibrarian.
- Whilst it's in Bootloader mode, select “Peak Bootloader” as destination in the top drop-down menu in SysEx Librarian. Then drag the “Peak-363.syx” (or “Peak-399.syx”) file (from the attached folder) into the main window.
- Highlight the file and press Play to send the firmware to the Peak. Peak will display the “% Received” of the firmware (WARNING the firmware update may not be finished when 100% is displayed – please wait for the bar to complete in SysEx Librarian to confirm the update has been sent successfully).
This may take 5–10 minutes to complete. The Peak will restart in Normal mode once the Firmware update is completed. Do not turn off the computer or Peak or disconnect the USB cable. - Once the above is completed, select “Peak” as the destination in SysEx Librarian and drag the “PeakFpga_353.syx” file (from the attached folder) into the main window. Highlight the file and press Play to send the FPGA to the Peak while the unit is in Normal mode. This may take 15–20 minutes to complete.
Peak will display the “FPGA Block” as the FPGA gets updated. - Once the above is completed, turn the volume dial fully anti-clockwise and disconnect any audio/MIDI cables from the back of the Peak. Go the Settings. In the 2nd System page, launch “Calibrate” to initiate the calibration of the unit.
This may take 5 minutes to complete.
Summit instructions:
- Download the attached 'Summit 1.1.zip' file from the bottom of this article and unzip it. You will find two files contained within it, 'Summit_Update_149.syx' and 'SummitFpga_618.syx'.
- Ensure the USB cable from Summit is connected to the computer. Start Summit in Bootloader mode by pressing the 3 buttons on the left side of the screen while powering on the Summit.
- Install and open SysEx Librarian snoize.com/SysExLibrarian.
- Whilst it's in Bootloader mode, select “Summit Bootloader” as the destination in the top drop-down menu in SysEx Librarian. Then drag the Summit_Update_149.syx file (from the attached folder) into the main window.
- Highlight the file and press Play to send the firmware to the Summit
Summit will display the “% Received” of the firmware (WARNING the firmware update may not be finished when 100% is displayed – please wait for the bar to complete in SysEx Librarian to confirm the update has been sent successfully).
This may take 5–10 minutes to complete. The Summit will restart in Normal mode once the Firmware update is completed. Do not turn off the computer or Summit or disconnect the USB cable. - Once the above is completed, select “Summit” as the destination in SysEx Librarian and drag the 'SummitFpga_618.syx' file (from the attached folder) into the main window. Highlight the file and press Play to send the FPGA to the Summit while the unit is in Normal mode. This may take 15–20 minutes to complete.
Summit will display the “FPGA Block” as the FPGA gets updated. - Once the above is completed, turn the volume dial fully anti-clockwise and disconnect any audio/MIDI cables from the back of the Summit. Go the Settings. In the 2nd System page, launch “Calibrate” to initiate the calibration of the unit.
This may take 5–10 minutes to complete.